fiat 500 key fob not working 500 Replacement Key Fob

It might be time to replace the battery if the 500 remote key fob is not working. However, if you replace the battery and it doesn't work the issue may be elsewhere.

United Locksmith specializes in the creation of new keys for classic cars. We have the tools as well as the parts required for this service.

Dead Coin Battery

The most frequent reason that your fiat punto locked keys in car 500 key fob will not lock or unlock the doors is due to a dead battery. The key fob comes with the battery of a coin-cell that will drain quickly if it is not used often enough. If your remote began to show signs of weakening like a loss of range or stopped working completely, the battery is probably dead.

Metal clips hold the battery securely inside the key fob. If the clips aren't secure, they could cause contact issues that prevent the remote from receiving power. Using a small flathead screwdriver, pull the retaining clip outwards to take out the battery and replace it with a new one. Choose a battery that is the same voltage, size, and specifications as the original.

The exposure to water can cause the key fob where to get a fiat key cut corrode or be damaged. Even a short bath in soapy, warm water can cause damage to the chip. It is recommended to keep your key fob in a dry area.

Water Damage

Damage to your water supply could be the reason for your key fob's inability to function properly. Key fobs are fitted with rubber seals that stop them from being damaged by light rain or splashes of water, but it is crucial to keep your car keys away from the pool, ocean and the washing machine!

The key fob is equipped with an electronic chip that sends a message to the immobilizer system in your car. The chip is what allows the 500 to be locked and started. If it gets wet it won't function.

You can clean the internal electronics of your key fob with isopropyl Alcohol or an electronic cleaner to determine if they are still good. It is recommended to replace the key fob if it's submerged in salt water instead of trying to fix it yourself.

While a replacement fob might cost you a little bit of money, it is much less expensive than paying for your Fiat 500 to be towed to the dealership and repaired! Plus, you can do it yourself with several easy steps. Be sure to use the right battery type before you attempt to open your key fob. You can find step-by-step instructions for any car keyfob online.

Faulty Chip

The chip inside the key fob communicates with your car's immobiliser system to ensure the vehicle is able to start when the correct key is used. If the chip is damaged or corrupted it won't allow your car to start no matter what you do.

A chip that is damaged can happen due to a variety of reasons, but most often it is due to water damage or an unresponsive battery. Regardless of the reason, it's an ideal idea to hand the work to a locksmith since they will be able to replace the chip quickly and at a reasonable cost.

If your key fob stops working after exposure to clean water from the tap or rain, remove the battery and wipe down the electronic component using a paper towel to ensure it is fully dry before putting it back into. If the key fob does not work, there is an opportunity that it is malfunctioning components and need to be replaced.

Some people will go to their dealer when in need of an entirely new Fiat key fob, but this can be a very expensive option. If you are looking for a low-cost solution to have your Fiat key fob fixed then look no further than United Locksmith. We have the equipment and know-how to get a replacement key for Fiat 500; saveyoke60.werite.net, needed to repair your Fiat key fob in a timely and professional way.

Faulty Receiver Module

Fiat key fobs send signals of up 50 feet away to the vehicle, which will unlock and close the doors (and start the vehicle for vehicles with automatic transmissions). There are a variety of reasons why the fob may stop working. This could be due to a dead battery, water damage, worn-out buttons as well as a receiver issue. signal interference or a malfunctioning chip.

If the fob was in a pocket which has suffered severe trauma (such as being dropped onto the floor, or washed in the washer), it may not be in a position to communicate with the Body Control Module (BCM) of the vehicle. This is because the BCM is a secure system that will only accept signals from a genuine key and not any other.

If this is the case, then you will need to replace your fob. A professional locksmith can handle the entire replacement process including programming a brand new key for your 500. They can even give you a clone fob that works exactly like the original (and costs only one-third of the price).