How to Replace a Kia Sportage Replacement Key

The key of many kia ceed key models has an electronic keyless entry system built in. This key typically resembles an remote control, and is able to be replaced with a fresh one from a Kia dealer or locksmith.

Key fobs are prone to malfunction due to a variety of reasons, including an empty coin battery, worn buttons or buttons, water damage, signal interference and a faulty receiver module. Here are some suggestions on how you can get your kia sportage key fob replacement Sportage replacement key to work again.

How to replace a smartkey or remote key?

The battery inside your Kia's smart key will eventually need to be replaced, whether it's a remote key or a push-to-start one, or a normal metal key that is not equipped with an electronic transponder. This is especially in the event that your car displays a message indicating that the remote or smart key has low battery power.

Luckily, it's a relatively simple process. In order to replace the battery in the key fob take the mechanical key from the slit at the back of the key fob and remove the cover. A small screw will be located inside the key fob to keep the battery in its place. Remove the old battery by removing the screw with a small screwdriver. Insert the new battery and close the slit on the key fob.

Once the key fob has an updated battery check it by pressing the locks and unlock buttons. You're good to go when the doors lock or unlock as expected. You can now use the Kia's hands-free lock/unlock feature when your fingers are cold or you have to run some errands in Brandon.

Note: Certain key fobs could need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) do not require programming a kia key fob. If you need to reprogramme your key, you'll need write down the key code's number on the tag for the key code.

How do you replace a dead battery?

If the Kia key fob doesn't respond to pressing the lock/unlock button, it is most likely that the battery is not fully charged. A low battery can also cause other issues, such as the check engine light coming on or the engine not cranking properly. Fortunately replacing the battery on the key fob is a relatively easy DIY project that requires just some basic tools.

Before starting the process be sure that your vehicle is turned off and all doors are shut. Find the small metal or a plastic piece on the bottom of the key fob. Jiggle it until the key is released. This key can be inserted into the driver door handle to unlock your car.

To replace the key fob battery, take off the rear cover and use a plier bar tool to release the latch that holds the black negative battery cable. Remove the old battery, and then orient the replacement battery so that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position and avoid excessive force to avoid damaging or bending the contacts made of metal.

After the new battery has been installed then turn the key fob off and back on in the ignition for a few times until the door locks cycle. You can then test the Kia's key fob to ensure it's working properly.

How do you replace the smart key

You can have a standard keyfob, or a Smart Key depending on the model of Kia Sportage. The smart key has an embedded mechanical key blade, however, the standard key fob does not. Both types of key fobs have batteries that will eventually need to be replaced. Fortunately, this is an easy task that takes only two minutes.

Before you start, you will want to ensure that you're on a flat surface with sufficient lighting and that your Kia is off. Keep in mind that the fob is made up of tiny parts that could fall should you not be careful.

The first step is to find the small release button on the lower backside of your fob. It's either a circular button or a rectangular slot. When you press it the mechanical key blade will come out and you will be able to open the key fob.

Once you have the key fob opened and you are able to take off the old battery and replace it. The new battery is the CR-2032, and it can be purchased through the internet or at a local auto parts shop. After you've finished, you should be able to lock, unlock and start your vehicle with your key fob even if the engine isn't running!

How to replace the mechanical key

The Kia key fob is a fantastic option that lets us lock and unlock our car at the click of a button. Like any device that is used, the Kia key fob can have issues at times. Luckily, there are steps that can be taken to resolve these issues and keep our key fobs in good working order over the long haul.

One of the most common problems is a low or dead battery. This can cause the fob to stop working completely or to work intermittently. If this is the case you should replace the battery with a fresh new one.

If this isn't enough to resolve the problem then try using a normal flathead screwdriver to open the fob's plastic casing. Be cautious not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob and make sure it is working correctly. Contact a dealer, or a locksmith to solve the issue in the event that the fob is not working. To avoid locking outs in the future, ensure you purchase an emergency key that can be able to work with all trunk and door cylinders.