How to Replace a Kia Sportage Replacement Key

The key on many Kia models comes with an entry system that is keyless in. The key can be compared to an remote control, and can be replaced with a brand new one from a Kia dealer or a locksmith.

Key fobs can stop working due to a number of reasons, such as an inactive battery, worn out buttons signal interference or water damage. Here are some suggestions on how to get your Kia Sportage replacement kia key key working again.

How do you replace the remote key or the smart key?

If your Kia comes with an intelligent key, remote key, push-to-start keys, or a regular non-transponder steel key the battery in these keys will eventually require replacing. This is especially when the car displays a message telling that the smart or remote key has low battery power.

It's a fairly simple procedure. To replace the battery of the keyfob remove your mechanical key from the slit on the back of the fob. Then, push the cover open. Inside the key fob there will be an incredibly small screw that holds the battery in the correct position. Remove the old battery by removing the screw with a small screwdriver. Install the new battery and then close the cut on the key fob.

When the key fob is equipped with an updated battery, test it by pressing the locks and unlock buttons. If the doors lock and unlock as expected, then you're set! You can now use the hands-free feature to lock and unlock your Kia when your fingers get cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a special programming machine that only the dealer or automotive locksmith can access. Other keys (non transponder metal keys) do not require programming. If your keys need to be reprogrammed, you must be aware of the key code number stamped on the tag of the key code and then record it in a safe place.

How do I replace the battery?

If the Kia key fob is unable to respond when you press the lock/unlock button, it's likely that the battery is insufficient. A battery that is not functioning properly could cause other problems like the check engine light flashing on or delayed engine cranking. Fortunately replacing the battery on the key fob is a simple DIY project that requires only the most basic tools.

Before you begin the process, make sure that your vehicle is off and that all doors are shut. Find the small metal or plastic piece that is located at the bottom of the key fob. Jiggle it until the key comes out. Then, you can insert the key into the driver's door handle to open your car.

To replace the key fob's battery, remove the cover from the back and use a plier bar tool to remove the latch that holds the black negative battery cable. Remove the old battery, and then align the replacement battery to ensure that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.

After the new battery has been installed and the key fob is turned on, turn it off and then turn it on in the ignition repeatedly until the door locks cycle. You can then test the Kia's key fob again to make sure it is working correctly.

How to replace a smart key

You could have the standard keyfob or Smart Key based upon the model of Kia Sportage. The smart key has an embedded mechanical key blade, while the standard keyfob does not. Both key fobs have a battery that will eventually require replacing. This is a simple procedure which takes just two minutes.

Before you get started it is essential to ensure that you are on a level surface with sufficient lighting and that your 2012 kia optima key fob is not on. Be aware that there are tiny parts inside the fob that can fall out if not cautious.

The first step is to find the small release button on the back of the lower part of the fob. It's either an oval or circular slot. You can open the key fob by pressing the button.

Once you have the key fob opened and you are able to take out the old battery and replace it. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. When you're done, the key fob should be able to lock, unlock, and start your vehicle even if it's not running.

How do you replace a broken mechanical key

The Kia key fob is an amazing feature that lets us lock and unlock our car at the press of one button. However, like all devices there are issues with it at times. There are ways to resolve these issues and ensure that our key fobs are in good condition for the long run.

One of the most frequent issues is a low or dead battery. This can cause the fob to stop working completely or to work intermittently. If this happens try replacing the battery with a new one.

If this does not solve the issue, use an ordinary screwdriver with a flat head to push the fob's plastic casing open. Be careful not to damage internal components, or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new kia key cost battery.

Once the new battery is in, close and open the doors using the mechanical key (every key fob in the Kia Fob Replacement has an emergency mechanical key that can fit in the slot). Test the key fob and verify that it's working properly. If the fob isn't working, call an expert locksmith or dealer to resolve the issue. Make sure they make you an emergency key that works in all the trunk and door cylinders, to avoid lockouts again.